Retake Your DEAD PHONE
I am modifyng this thread coz i noticed many of the users not able to flash dead fone.
Through this method you can retake your Dead Phone.
Phone May Dead Due to error occur while flashing or Software error occur due to some other cause
In any case if your phone Dead, You can retake it
In order to retake your phone
1. Download Phone OS (With contain .mcu, .ppm& .image) by NAVIFIRM OR SHRAK-MOBILE
2. Install Phoenix
GO TO:
C:\Program Files\Nokia\Phoenix\Products
Create a Folder and Name It Depending Upon your RM Version
E.g.: For 6300 as “RM-217”
For 5130 as “RM-495”
Then you can see as
C:\Program Files\Nokia\Phoenix\Products\RM-217
Copy you downloaded file (.mcu, .ppm, &.image) to this folder
>now download..the .exe firmware required for dead flashing from
now install this firmware on ur pc..
restart ur pc
run Jaf
Click On BB5>>
Remove tick mark from "normal mode"
Put tick in "Dead USB" &"Manual Flashing"
do not select offline mode..(its shown in the pic but plz dont select any mode)
untick the CRT 308...
NOW Put tick in “Use INI”
Wait for a while
An additional widow as shown in figure will appear
Select your phone
MCU; PPM; CNT buttons in JAF will automatically Glow in Green (i.e., No need to select separately as done in Flashing: if did not glow all (it is due to error), never open separately, it should open automatically)
Put tick in “Run INI”
Click on “FLASH”
Click “Yes”
Wait for a Minute
A window appear as Shown
after that..in the next window..
PUT YOUR one HAND IN POWER BUTTON and other in MOUSE. Click “YES”. (Within 1 sec i.e., just after click “YES”)AT THE SAME TIME PRESS YOUR POWER BUTTON FOR more or less 4 sec
Remove your hand from power button
Will show command like this
Wait for 4 to 5 minute
When it shows “DONE”
Change Phone Mode To “NORMAL”
in the above image..its OFFLINE..but ..u should change it to NORMAL..
THATS IT UR DEAD FONE IS ALIVE AGAIN...
I am modifyng this thread coz i noticed many of the users not able to flash dead fone.
Through this method you can retake your Dead Phone.
Phone May Dead Due to error occur while flashing or Software error occur due to some other cause
In any case if your phone Dead, You can retake it
In order to retake your phone
1. Download Phone OS (With contain .mcu, .ppm& .image) by NAVIFIRM OR SHRAK-MOBILE
2. Install Phoenix
GO TO:
C:\Program Files\Nokia\Phoenix\Products
Create a Folder and Name It Depending Upon your RM Version
E.g.: For 6300 as “RM-217”
For 5130 as “RM-495”
Then you can see as
C:\Program Files\Nokia\Phoenix\Products\RM-217
Copy you downloaded file (.mcu, .ppm, &.image) to this folder
>now download..the .exe firmware required for dead flashing from
http://allnokia.ru/firmware/now install this firmware on ur pc..
restart ur pc
run Jaf
Click On BB5>>
Remove tick mark from "normal mode"
Put tick in "Dead USB" &"Manual Flashing"
do not select offline mode..(its shown in the pic but plz dont select any mode)
untick the CRT 308...
NOW Put tick in “Use INI”
Wait for a while
An additional widow as shown in figure will appear
Select your phone
MCU; PPM; CNT buttons in JAF will automatically Glow in Green (i.e., No need to select separately as done in Flashing: if did not glow all (it is due to error), never open separately, it should open automatically)
Put tick in “Run INI”
Click on “FLASH”
Click “Yes”
Wait for a Minute
A window appear as Shown
after that..in the next window..
PUT YOUR one HAND IN POWER BUTTON and other in MOUSE. Click “YES”. (Within 1 sec i.e., just after click “YES”)AT THE SAME TIME PRESS YOUR POWER BUTTON FOR more or less 4 sec
Remove your hand from power button
Will show command like this
Wait for 4 to 5 minute
When it shows “DONE”
Change Phone Mode To “NORMAL”
in the above image..its OFFLINE..but ..u should change it to NORMAL..
THATS IT UR DEAD FONE IS ALIVE AGAIN...
0 comments:
Post a Comment